Part Number : NPC04S

802.3af/at Active to Passive POE Gigabit Converter

PCBA Model : BPL-1512

Only PCBA Board

Introduction

The PoE Converter effectively allows any PoE device to become compliant with 44-57V 802.3af/at PoE standards. This conveniently standardizes power management of your system by introducing compatibility of passive PoE devices with standard 802.3af/at switches. This device can convert the standard 802.3af/at PoE source to the passive power (pin 4,5/7,8) via POE Converter, in addition it can switchable the volt output to 12V/19V/24V by DIP switch. When there had a standard PoE switch (802.3af/at) in the network architecture, but the PoE device (PD) is Passive PoE type, then you can use this POE Converter to convert the PoE power type, it is very convenient and cost effective solution. It is perfect for transforming access points that use a passive PoE design into 802.3at compliant devices. Other applications also include deploying passive PoE IP cameras with standard 802.3af/at PoE switches.

Highlight Features

  • Complying with IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3ab 1000Base-T IEEE 802.3at PoE+, IEEE 802.3af PoE standards.
  • PoE (PD) support IEEE 802.3at PoE+, IEEE 802.3af PoE.
  • Supports 10/100/1000Mbps Gigabit Ethernet.
  • Supports PoE voltage output with 12V / 19V /24V three range adjustable.
  • With hardware protection design the device will not cause any damage while changing the voltage output during operation.
  • Up to 100 meters (328 feet) application.
  • Supports to Short-circuit Protection.
  • Plug and Play, no software required.
  • Supports desktop or wall mounting installation and multiple units combination.

Hardware Specification

Product 802.3af/at to Passive 12V/19V/24V POE Gigabit Converter
Main Chip Solution Microsemi PD70200
Standard IEEE 802.3 10BASE-T

IEEE 802.3u 100BASE-TX

IEEE 802.3ab 1000BASE-T

IEEE 802.3af Power over Ethernet (PoE)

IEEE 802.3at Power over Ethernet Plus (PoE+)

Network Media 10BASE –T: UTP Cat. 3 or up

100BASE-TX : UTP Cat. 5 or up

1000BASE-T: UTP Cat. 5 or up

Data Transfer Rate 10/100/1000Mbps (Half-duplex),

20/200/2000Mbps (Full-duplex)

Data Pin PIN 1/2, 3/6 & 4/5, 7/8
PoE Type Input : End-span (Type-A): 1/2,3/6 ; Mid-span (Type-B): 4/5,7/8

Output : Mid-span (Type-B): 4/5,7/8

Power Interface Input : RJ45 PoE In

Output : RJ45 PoE out

Power Requirement 802.3af/at PoE Power Source , Input Voltage: 44 ~ 57Volt
Passive PoE Output Voltage 12V/ 19V/ 24V three range adjustable
LED Definition PoE Output LED  x3

l DC 12V output: 12V Light on

l DC 19V output: 19V Light on

l DC 24V output: 24V Light on

Temperature Operating : 0° to 55° C , Storage: -40° to 70° C
Humidity Operating : 10% to 90% non-condensing

Storage: 5% to 90% non-condensing

Dimension

( W x D x H )

NPC04S : 84.48*80*39.5 mm

BPL-1512 : 53*36mm

Case of material ABS
Weight NPC04S : 97.6g

BPL-1512 : 40.5g

Certifications TBD

** Specifications can be negotiated separately according to needs.

** Specifications can be negotiated separately according to needs.